RK3588 eMMC 32GB/64GB/128GB Custom, WF-C3588-R5, AndroidSBC, Zurich

TL;DR: RK3588 eMMC 32GB/64GB/128GB Custom

SHENZHEN, China, September 12, 2026 - The WF-C3588-R5 board line at Wanlin Longgang closed lot 249 this week. 28,925 units are now booked for Zurich, Switzerland, shipped FOB with the full certification file attached.

AndroidSBC release of the nine-variant custom RK3588 motherboard platform for OEM and ODM projects serving Zurich, Switzerland. The nine custom variants run from a custom Android motherboard through to a core-board-plus-carrier programme, all on the same Rockchip RK3588 octa-core 8nm silicon. AndroidSBC builds the line at the Longgang source factory in Shenzhen, with variant-specific I/O, thermal and enclosure options tied to the deployment profile. A Zurich buyer can hold one platform, one firmware image set, and one documentation format across custom Android, industrial, SOM, signage, kiosk, robotics, NVR, edge AI and ARM PC work.

About AndroidSBC and the Rockchip RK3588 Board Family

Wanlin Manufacturing Group builds the WF-C3588 at its Longgang plant in Shenzhen and sells it overseas through AndroidSBC. The programme covers nine custom motherboard categories on the Rockchip RK3588 octa-core 6 TOPS NPU platform, which is unusual for a single source factory: most suppliers specialise in one category. That breadth is what Switzerland importers tend to notice first, because it lets a Zurich distributor quote a custom Android smart display and a custom industrial controller on the same purchase order. Alongside the boards, Wanlin runs the OEM branding line, the ODM carrier design desk and the certification desk that produces the CE, FCC, UKCA, RoHS and IEC 62368-1 documentation for each shipment.

WF-C3588-R5 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-R5 (Custom Robotics and AGV Control Board) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Switzerland importers sourcing the WF-Series, the 8GB + 32GB (WF-C3588-R5-B) variant is the typical configuration for the custom robotics controller programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Robotics and AGV Control Board for Switzerland Buyers

For Switzerland procurement teams, the first surprise on the custom robotics and agv control board line is rarely technical. It is that the sample arrives on time and the production lot does not, because the Rockchip RK3588 allocation cannot be conjured from broker stock when a 28,925-unit order is confirmed. The second risk sits in the firmware image. Boards that pass a bench boot can still fail the certified stack the buyer's channel requires, and that gap usually appears during inbound inspection rather than before shipment.

The third exposure is the file behind the mark. A CE stamp without a dated test report and a Declaration of Conformity is a marking without substance, and the moment it matters is the moment a Switzerland customs officer asks for the underlying document. AndroidSBC answers this by doing the customization, the software burn and the documentation at the Longgang plant on every lot, with a per-unit QR that traces back to the burn-in record. For Zurich importers serving custom Android, industrial, signage, kiosk, robotics, NVR, edge AI and desktop verticals, the nine WF-C3588 custom variants cover the AGV controllers, AMR mainboards, service robots, inspection robots, quadruped platforms, SLAM navigation, robot vision, fleet dispatch terminals, and charging stations deployment lanes directly, with three memory configurations per variant.

Buyers in Switzerland tend to ask about the local mark before they ask about price. In Switzerland the market follows CE-aligned rules without EU membership, and OFCOM registration applies to radio equipment. AndroidSBC handles that by preparing the destination-market file covering CE-aligned conformity with OFCOM radio interface registration administered by OFCOM alongside the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), with the lot routed through Port of Rotterdam as the inland gateway on the Rotterdam to Yantian lane.

Competitive Comparison: WF-C3588-R5 vs Competing RK3588 Boards

Three families of board chase the same custom robotics and agv control board socket. The first is catalogue hardware with fixed memory and fixed I/O, the second is re-badged stock where nobody owns the schematic, and the third is a real custom platform built by the factory that runs the SMT line. The WF-C3588-R5 belongs to the third family and separates itself on Rockchip RK3588, on customization depth from schematic to firmware, and on a certified image burned per lot.

• vs paired PC-plus-MCU controllers: the WF-C3588-R5 runs vision, navigation and fleet logic on one board and hands only the power stage to the drive electronics.
• vs generic SBC robot builds: the CAN, multi-serial and real-time options come validated on the reference carrier instead of being patched in by the integrator.
• vs cloud-vision robots: SLAM and obstacle detection stay on the 6 TOPS NPU, so the robot keeps navigating when the warehouse WiFi drops.
• vs module resellers: custom I/O changes are executed by the Longgang engineering desk with the test bench that will validate them.

Global Custom Robotics Control Board Market Trends

The Custom Robotics Control Board curve is what Switzerland importers read before committing to a custom robotics and agv control board programme. The number they quote is the Edge AI hardware segment at USD 26.9 billion in 2025 with a 32.7 percent CAGR to USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), which serves as the closest public proxy for the silicon demand behind custom RK3588 boards. For Zurich that resolves into three demand patterns across the WF-C3588 order book:

• Warehouse AGV fleet: an automation vendor runs SLAM and fleet dispatch on the board with dual GbE back to the coordinator.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-R5 board carries that headroom without a board change.
• Inspection quadruped: a platform maker runs gait control and inspection vision on isolated cores under PREEMPT_RT.

The Custom Robotics Control Board outlook in Switzerland is being read less as a demand question and more as a supply-chain question, because demand has outrun reliable allocation.

Across those three segments, Zurich procurement has been shifting from spot quotes to framework agreements with a one-lot-per-month cadence, particularly where a custom Android, industrial, signage or robotics programme needs a twelve-month shipping window.

Partner Success Story: Novara Interactive in Zurich, Switzerland

Novara Interactive, an education display brand serving the Switzerland market, deployed 6,900 custom WF-C3588-S3 interactive whiteboard boards for a district rollout. The rollout covered the warehouse agv fleet, inspection quadruped, and agriculture robot workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 6,900 custom WF-C3588-S3 interactive whiteboard boards for a district rollout
• Region: Zurich, Switzerland
• Models used: WF-C3588-R5 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Yantian with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Rotterdam as the inland gateway via the Rotterdam to Yantian lane

"EDLA certification and a classroom launcher were both factory deliverables. The touch panel routing was custom, the boot animation is ours, and eight hundred classrooms enrolled against the MDM in the first fortnight."

- Elise Tremblay, Head of Hardware

Field Report: a school district rollout in Zurich, where 28,925 units of the WF-C3588-R5 board are being installed in classroom device carts

Reporter Xu Feng, on the ground in Zurich, Switzerland. The district took delivery of the order and dispatched installation crews to eight sites. Each WF-C3588-R5 unit was sealed into a ruggedised chassis running a managed Android image with the education services stack pre-provisioned for the district tenant, and the fleet enrolled against the MDM the same week.

Radiated emissions on the sampled units came in below the internal limit with margin, which the compliance engineer noted as consistent with the last four lots.

The inspection confirmed three things on the spot: the WF-C3588-R5 units hold the burn-in with a yield above 99.51 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE-aligned conformity with OFCOM radio interface registration administered by OFCOM, cleared for entry at Port of Rotterdam as the inland gateway on the Rotterdam to Yantian lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that Switzerland importers can hand straight to their customs broker.

Filed by Xu Feng, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-R5 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-R5 (Custom Robotics and AGV Control Board) as the lead SKU for Zurich and Switzerland programmes:

• Warehouse AGV fleet: an automation vendor runs SLAM and fleet dispatch on the board with dual GbE back to the coordinator.
• AMR delivery robot: a service robot pairs NPU navigation with a custom carrier that routes the sensor stack.
• Inspection quadruped: a platform maker runs gait control and inspection vision on isolated cores under PREEMPT_RT.
• Cleaning robot fleet: a facility operator runs coverage planning and obstacle detection locally with nightly model updates.
• Charging station control: the board coordinates dock sequencing, battery telemetry and fleet handshakes.
• Agriculture robot: a field robot runs row detection on the NPU offline, kilometres from the nearest access point.
• Remote monitoring link: a fleet operator streams diagnostics over the optional 5G seat to a central depot.
• Robot vision retrofit: an older fleet gains NPU vision without replacing the drive electronics.

Partnership Models for Zurich Buyers

For Zurich distributors and brand owners, AndroidSBC opens the custom robotics and agv control board line under three contract shapes:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

Whichever structure a Switzerland partner selects, the lot leaves Longgang with the same certification pack and the same test flow. The standard entry point on the WF-C3588-R5 is the 8GB + 32GB (WF-C3588-R5-B) configuration at MOQ 5,000 units per shipment, 1-3 days to sample and 15-30 days to mass production.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: The customization scope runs across five layers: hardware (PCB, PCBA, I/O, memory, storage), thermal (fanless passive, vented, wide-temperature, conformal coating), software (custom ROM, custom Linux, pre-installed apps, OTA), branding (logo, packaging, boot animation, SKU labels), and compliance (the certification file assembled for the exact configuration you ship). Most Switzerland partners change two or three layers on a standard variant rather than commissioning a full custom run.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Custom ROM, custom BSP and custom SDK work are all part of the ODM tier. AndroidSBC builds the Android image (12, 13, 14 or 15, GMS or AOSP), ports the Linux BSP to your carrier revision, and releases the SDK modules your team needs under NDA. The engineering desk carries the port itself, so a Switzerland integrator is not left debugging an unmodified vendor BSP against a carrier it was never designed for.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: Yes. The RK3588 NPU runs INT4, INT8, INT16, FP16, BF16 and TF32, and AndroidSBC supports model deployment through the Rockchip RKNN-Toolkit2, with quantization from PyTorch, ONNX, TensorFlow, Caffe and MXNet. As part of the ODM tier, the engineering desk walks your model from framework to RKNN format and validates it on the actual board configuration you are shipping, not a reference unit. Model files are versioned so a retrained model can be pushed to field units through OTA without a board swap.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: The structure is deliberately two-speed: 1-3 days for a standard-variant sample so a Switzerland project team can start immediately, and 15-30 days to mass production on a custom run once the design freezes. MOQ is 5,000 units per shipment on standard variants, with custom and pilot quantities negotiated against the annual volume commitment.

What certifications does a custom board need for Switzerland, and who handles them?

Answer: Yes, and the file travels with the goods. The pack covers CE, FCC Part 15, UKCA, RoHS 2.0, REACH and IEC 62368-1 with the EMC and safety reports for your configuration, dated within the prior year. AndroidSBC confirms any Switzerland-specific addition at quotation stage, which is the point where the answer is still useful rather than expensive.

How long will AndroidSBC keep supplying a custom board?

Answer: The commitment is seven years minimum on supply, with security patches back-ported across the Android and Linux firmware tracks and OTA infrastructure for pushing firmware and RKNN model updates to deployed units. Long-lifecycle programmes in industrial, signage and robotics usually ask for the term in writing, and it is written.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes. AndroidSBC ships DDP to Amazon FBA warehouses in the US, EU and Japan, and to nominated 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Carton labelling and pallet configuration follow FBA inbound requirements, the export declaration names the Wanlin Longgang source factory as the place of origin, and each pallet carries a per-unit barcode that traces back to the burn-in record for downstream RMAs.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: Target DOA is 0.3 percent across twelve months. RMA works by returning the WF-C3588-R5 unit to Longgang with its burn-in barcode; replacements ship inside ten business days. Since each unit is traceable to its burn-in and configuration record, partners typically receive a root-cause note with the replacement rather than a silent credit.

Contact AndroidSBC: Start Your WF-C3588-R5 Sourcing Conversation

AndroidSBC is the export channel for the Wanlin WF-C3588 custom board line. Buyers in Zurich and Switzerland looking to source the WF-C3588-R5 straight from the source factory can use any of the following:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE-aligned conformity with OFCOM radio interface registration for Switzerland, administered by OFCOM, entering at Port of Rotterdam as the inland gateway on the Rotterdam to Yantian lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

The export desk asks for three things on a first enquiry: annual volume, customization scope and Incoterm. Provide those and a per-lot quote plus the WF-C3588 MOQ matrix comes back within two business days.